Dear all,
we have just released a new version Cruiser Suite SE TP Full Unlocker v1.05 with full GDFS reconstruction feature. For work you need UC-20 TestPoint cable and Cruiser Suite dongle. You can buy both from any of our official resellers.
IMPORTANT: All other TestPoint solutions force the phone address bus pins to 3.3V which is exceeding its maximal allowed voltage almost twice. Only the UC-20 TP cable was designed to prevent this and avoid likely flash chip damage. UC-20 TestPoint box is a current limited variable voltage power supply with connection sensing feature.
CruiserSuite TP Full Unlocker v1.05 release info:
documentation updated
minor updates
All features of CruiserSuite TP Full Unlocker software:
Component of Cruiser Suite (once you have Cruiser Suite dongle, you can use it).
Simple to use & failsafe
Supports full unlock of all DB2020 plattform based SonyEricsson phones (all current DB2020 CIDs)
Supports full unlock of DB2012 plattform based phones, CID 50, 51, 52, 53; by one (single) TP
Supports full unlock and repair of specific DB2010 K310, K510, W300, W810, Z530. Specific means DB2010 / CID 49, with DB2012 chip on the PCB - those models that were not previously supported by Cruiser+
Recovery mode feature for all supported phone models (for failed EROM write)- by using testpoint stage 2
This software is for all users who can disassemble the phone - also for inexperienced ones. (For disassembling phones, we recommend to read proper SonyEricsson service manuals.)
Unlocking via TP Full Unlocker does not destroy phone calibration data (so typical for SadTool ... )
For the phone safety, TestPointing requires UC-20 TP cable.
Unlike other amateur solutions which use external battery connection to the TP, our software uses specially designed UC-20 cable which can handle different bus voltages and prevents any potential flash chip damage.
TP is done in two stages. Once you complete TP stage 1 you don't need to repeat it anymore. Phone is then bootable via the 2nd testpoint anytime.
PDF manual is available after installation as usual in Documents folder
You can download the latest version from our Downloads section or directly from this Rapidshare link.
Don't forget to tell everywhere that CruiserSuite is the First on the market who provide Full Unlock of DB2012 and DB2010 over 1 SINGLE TestPoint. Everybody else (DreamBox and SadTool) requires you to do testpointing in 2 stages.
ENJOY!
[You must be registered and logged in to see this link.]
we have just released a new version Cruiser Suite SE TP Full Unlocker v1.05 with full GDFS reconstruction feature. For work you need UC-20 TestPoint cable and Cruiser Suite dongle. You can buy both from any of our official resellers.
IMPORTANT: All other TestPoint solutions force the phone address bus pins to 3.3V which is exceeding its maximal allowed voltage almost twice. Only the UC-20 TP cable was designed to prevent this and avoid likely flash chip damage. UC-20 TestPoint box is a current limited variable voltage power supply with connection sensing feature.
CruiserSuite TP Full Unlocker v1.05 release info:
documentation updated
minor updates
All features of CruiserSuite TP Full Unlocker software:
Component of Cruiser Suite (once you have Cruiser Suite dongle, you can use it).
Simple to use & failsafe
Supports full unlock of all DB2020 plattform based SonyEricsson phones (all current DB2020 CIDs)
Supports full unlock of DB2012 plattform based phones, CID 50, 51, 52, 53; by one (single) TP
Supports full unlock and repair of specific DB2010 K310, K510, W300, W810, Z530. Specific means DB2010 / CID 49, with DB2012 chip on the PCB - those models that were not previously supported by Cruiser+
Recovery mode feature for all supported phone models (for failed EROM write)- by using testpoint stage 2
This software is for all users who can disassemble the phone - also for inexperienced ones. (For disassembling phones, we recommend to read proper SonyEricsson service manuals.)
Unlocking via TP Full Unlocker does not destroy phone calibration data (so typical for SadTool ... )
For the phone safety, TestPointing requires UC-20 TP cable.
Unlike other amateur solutions which use external battery connection to the TP, our software uses specially designed UC-20 cable which can handle different bus voltages and prevents any potential flash chip damage.
TP is done in two stages. Once you complete TP stage 1 you don't need to repeat it anymore. Phone is then bootable via the 2nd testpoint anytime.
PDF manual is available after installation as usual in Documents folder
You can download the latest version from our Downloads section or directly from this Rapidshare link.
Don't forget to tell everywhere that CruiserSuite is the First on the market who provide Full Unlock of DB2012 and DB2010 over 1 SINGLE TestPoint. Everybody else (DreamBox and SadTool) requires you to do testpointing in 2 stages.
ENJOY!
[You must be registered and logged in to see this link.]
